Search:

Type: Posts; User: Far Rider; Keyword(s):

Page 1 of 20 1 2 3 4

Search: Search took 0.05 seconds.

  1. Replies
    160
    Views
    1,663

    Manana. I've been up since 5 and I'm whipped. I...

    Manana. I've been up since 5 and I'm whipped. I ordered the wrong size clamps for the capcans and had to reorder. Found out that Weber shorted me a 5W resistor and they're sending it out. Ran out...
  2. Replies
    20
    Views
    222

    I thought so, it just looked like the board was...

    I thought so, it just looked like the board was already mounted.
  3. Replies
    20
    Views
    222

    Really nice Terry. Do you populate the turret...

    Really nice Terry. Do you populate the turret board inside the amp as opposed to outside?
  4. Replies
    160
    Views
    1,663

    I'm starting to ohm out the connections. What...

    I'm starting to ohm out the connections. What should I be looking for?

    Also, should I be using the red/white pair(660v) or the 2 red wires (720v) for connection to the rectifier? I asked CJ and...
  5. Replies
    160
    Views
    1,663

    I said as much to CJ at Weber, and he said he did...

    I said as much to CJ at Weber, and he said he did the drawing to as closely match the layout. I've sent several e-mail with questions and he's been very good at answering my questions. I've said...
  6. Replies
    160
    Views
    1,663

    https://i.imgur.com/LB8E9md.jpg ...

    https://i.imgur.com/LB8E9md.jpg

    https://i.imgur.com/jmHeqh4.jpg


    https://i.imgur.com/acNCT8K.jpg
  7. Replies
    160
    Views
    1,663

    Terry, I knew this drawing was going to give me...

    Terry, I knew this drawing was going to give me problems. Do you see a mistake in it? I saw the resistor going to pin 1 of Capcan 6 and the other side on the daughterboard being connected by a wire...
  8. Replies
    160
    Views
    1,663

    No, the pic doesn't show it but it's above it and...

    No, the pic doesn't show it but it's above it and clear. My camera has a flash problem. The boards aren't mounted yet.
  9. Replies
    160
    Views
    1,663

    Here is the daughterboard. There's going to be a...

    Here is the daughterboard. There's going to be a lot of flying connections, so I will be heat shrinking a lot:

    https://i.imgur.com/h93gdJz.jpg

    Got the faceplates and controls mounted:
    ...
  10. Replies
    20
    Views
    222

    Looking good Terry.

    Looking good Terry.
  11. Replies
    160
    Views
    1,663

    Pic of the new board... ...

    Pic of the new board...


    https://i.imgur.com/6Q1PmpG.jpg
  12. Replies
    160
    Views
    1,663

    That 210 possible combinations! :yikes:

    That 210 possible combinations! :yikes:
  13. Replies
    160
    Views
    1,663

    Yes Obiwan. To ground?

    Yes Obiwan. To ground?
  14. Replies
    160
    Views
    1,663

    Can anyone help me figure out which are the...

    Can anyone help me figure out which are the heater pair? Is it the Green\Green or the Yellow\Yellow or something else? This transformer is fucking with my mind. I'm used to ClassicTone, where...
  15. Replies
    160
    Views
    1,663

    Thanks Terry! A fountain of knowledge he is.

    Thanks Terry! A fountain of knowledge he is.
  16. Replies
    160
    Views
    1,663

    All I had to go by was the packing list that had...

    All I had to go by was the packing list that had the values but only listed their stock number. I figured out the .1uF because there were 6 of them.

    CJ just got back to me with the values, and...
  17. Replies
    160
    Views
    1,663

    This was all that was on the ones, that by...

    This was all that was on the ones, that by process of elimination, I couldn't figure out..

    MA102J - 630V
    MA103J - 630V
    MA223J - 630V
    MA473J - 630V

    Waiting for him to get back to me.
  18. Replies
    160
    Views
    1,663

    I sent an e-mail to CJ at Weber today asking him...

    I sent an e-mail to CJ at Weber today asking him to help me identify the values of the caps since there are no markings or descriptions of what is what. God is testing me. :hmm:
  19. Replies
    160
    Views
    1,663

    (Conscience speaking) Yes, STFU!!!!!!!!

    (Conscience speaking) Yes, STFU!!!!!!!!
  20. Replies
    160
    Views
    1,663

    Am I whining too much? I hate that.

    Am I whining too much? I hate that.
  21. Replies
    160
    Views
    1,663

    :laugh2:

    :laugh2:
  22. Replies
    160
    Views
    1,663

    I wanted to see how the new board was going to...

    I wanted to see how the new board was going to fit. Even with my tallest standoffs, it barely clears the transformer bolts by a cunt hair.

    https://i.imgur.com/yv15m36.jpg

    Here's a comparison...
  23. Replies
    160
    Views
    1,663

    Got the transformers, power tube and rectifier...

    Got the transformers, power tube and rectifier sockets installed.

    https://i.imgur.com/F7LQSli.jpg
  24. Replies
    160
    Views
    1,663

    It's that hour time difference. That and 5 cats...

    It's that hour time difference. That and 5 cats waking me up for breakfast. :laugh2:
  25. Replies
    160
    Views
    1,663

    I saw that and was going to ask about it. As a...

    I saw that and was going to ask about it. As a side note, I get really excited when I recognize a circuit and what components are in it. Maybe some of this is sinking in after all.
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4