Search:

Type: Posts; User: T-Rex; Keyword(s):

Page 1 of 20 1 2 3 4

Search: Search took 0.05 seconds.

  1. Replies
    20
    Views
    222

    I do all the turretboard work on a Panvise, then...

    I do all the turretboard work on a Panvise, then drop the board, wired into the chassis.
  2. Replies
    20
    Views
    222

    Some more progress. Relocated the fuses, wired up...

    Some more progress. Relocated the fuses, wired up the switches and the rest of the PT and fuses / IEC plug. Finished the filament wiring. Ready to start wiring the turretboard.
    ...
  3. Replies
    160
    Views
    1,659

    No mistake on the 1K resistor, I assumed that you...

    No mistake on the 1K resistor, I assumed that you are tagging one end of the "common" resistors to the daughter board is all, and didn't see the 1K between the last 220K and the 10K on the daughter...
  4. Replies
    160
    Views
    1,659

    I was asking about the resistor from cap can 3 to...

    I was asking about the resistor from cap can 3 to cap can 6?
  5. Replies
    160
    Views
    1,659

    By chance are you short the 1K 2watt resistor on...

    By chance are you short the 1K 2watt resistor on your daughter board?
  6. Replies
    20
    Views
    222

    Some progress this morning. Built and wired up...

    Some progress this morning. Built and wired up the reservoir filter cap board, blanked off the can cap holes that won't be used, wired the rectifier socket and wired the choke up to the cap board,...
  7. Replies
    160
    Views
    1,659

    As Gator said, Grn--Grn is the heater coil, but...

    As Gator said, Grn--Grn is the heater coil, but remember you must ground the CT of that coil.
  8. Replies
    160
    Views
    1,659

    Jimi, The three digit codes indicate the uF...

    Jimi, The three digit codes indicate the uF values.

    www.radiodaze.com/capacitor-markings/
  9. Replies
    160
    Views
    1,659

    I think I have a shoe horn from the 60's lying...

    I think I have a shoe horn from the 60's lying around somewhere if you need it.
  10. Replies
    160
    Views
    1,659

    You could easily solder both the 1.5K and 100uF...

    You could easily solder both the 1.5K and 100uF cap on the far right of your board onto one turret. Either stack them or fan one of the two components off to the right hand side of the board. Like...
  11. Replies
    160
    Views
    1,659

    If you have more turrets on the new board than...

    If you have more turrets on the new board than needed, the boards cut to length easy enough with a hack saw.

    If you have two different heater wire directions, install a small 3 lug terminal strip...
  12. Replies
    160
    Views
    1,659

    If the o.d. of those cap cans allow the can's...

    If the o.d. of those cap cans allow the can's outside diameter to fit through the socket hole, you could always use the fiber mount on the bottom side of the chassis, in addition to the clamps, as a...
  13. Replies
    160
    Views
    1,659

    AES or TubeDepot has the rings. Weber does some...

    AES or TubeDepot has the rings. Weber does some strange shit on rectifiers. That is not a tube rectifier, my guess is some sort of version of their "copper cap" S.S. rectifier cap.
  14. Replies
    160
    Views
    1,659

    Jimi, I did a quick search on the web for those...

    Jimi, I did a quick search on the web for those who have built a Weber 6H50. It looks like most people went with the conventional can cap mounting rings to secure those can caps to the chassis.
    ...
  15. Replies
    20
    Views
    222

    I'm not sure how much more noticeable it would be...

    I'm not sure how much more noticeable it would be on the Bassman, as the HT voltage on the Bassman is about 35 volts higher on Fenders specs on the power tubes, in comparison to the 59 Twin specs....
  16. Replies
    20
    Views
    222

    Actually the only difference in the 59 Tweed...

    Actually the only difference in the 59 Tweed Bassman and the Tweed Twin, is the Twin has an extra set of power tubes, and the mA of the Twin PT is boosted to handle the extra set of power tubes, but...
  17. Replies
    20
    Views
    222

    The man knows his Fenders. Ding, ding, ding......

    The man knows his Fenders. Ding, ding, ding...
    .we have a winner !
  18. Replies
    20
    Views
    222

    Some progress today. Mounted the iron, knocked...

    Some progress today. Mounted the iron, knocked out the rectifier socket hole, mounted the power sockets. Relocated the turretboard to add the power board.


    https://i.imgur.com/by3Wu6g.jpg?1

    ...
  19. Replies
    20
    Views
    222

    This is the chassis that I'm using. Granted it is...

    This is the chassis that I'm using. Granted it is for a stock 2204 50watt Marshall, but it allows me blank space to cut in my laydown PT, and this amp model that I'm building originally came in a 4"...
  20. Replies
    20
    Views
    222

    The chassis is here, and at 10" longer than I'm...

    The chassis is here, and at 10" longer than I'm used too, I feel lost. The turretboard is staked too, need to build a Power capacitor turretboard yet, cut the hole for the laydown power transformer....
  21. Replies
    160
    Views
    1,659

    They sell the single row too, don't know if you...

    They sell the single row too, don't know if you saw that too

    https://www.tubesandmore.com/products/turret-strip-127mm-x15875mm-loaded-11-turrets
  22. Replies
    160
    Views
    1,659

    If you are disappointed with the turretboard,...

    If you are disappointed with the turretboard, they sell pre-staked turretboards for Hiwatts on most of the supply houses that may be sturdier.
    ...
  23. Replies
    160
    Views
    1,659

    I will be most interested in hearing your final...

    I will be most interested in hearing your final tone evaluation of your build. I had thought in the past about doing what you are starting on. Just never got around to it.
  24. Replies
    160
    Views
    1,659

    yes The red HT wires that go to pins 4 & pin...

    yes

    The red HT wires that go to pins 4 & pin 6, also have a wire that is shown as leaving pin 6 that becomes your bias voltage feed wire. That bias tap feed wire could come off of either of those...
  25. Replies
    160
    Views
    1,659

    yes

    yes
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4