Search:

Type: Posts; User: Ghostman; Keyword(s):

Page 1 of 20 1 2 3 4

Search: Search took 0.06 seconds.

  1. All kinds of finished amps around here. Nicely...

    All kinds of finished amps around here. Nicely done.
  2. Replies
    20
    Views
    331

    I made the mistake to click the link. Fuck I hate...

    I made the mistake to click the link. Fuck I hate CharvelDan. Good riddance of my exit from that place.
  3. Replies
    15
    Views
    189

    https://i.imgur.com/e1crXi9.gif

    https://i.imgur.com/e1crXi9.gif
  4. Replies
    15
    Views
    189

    Micky yeah, a bass control. I was also thinking...

    Micky yeah, a bass control. I was also thinking if you created a band-reject filter network for a Mid control instead of either the traditional "Tone" or the Bass control in your posted circuit.
  5. Replies
    15
    Views
    189

    Alternate Guitar Tone Control

    The tone knob on almost every guitar is to roll of the high frequencies. Has anyone tried a different variant of rolling off the bottom end, or maybe even a mid frequency cut/scoop?

    Just curious...
  6. Replies
    61
    Views
    1,084

    https://i.imgur.com/REW8QDU.gif

    https://i.imgur.com/REW8QDU.gif
  7. Replies
    61
    Views
    1,084

    you are certifiable. :D I can barely live...

    you are certifiable. :D

    I can barely live without one. I really don't like time based effects outside the loop, and also running high gain without a noise gate in the loop. When I run my JKD, I...
  8. Replies
    61
    Views
    1,084

    No loop?!? https://i.imgur.com/wAA2x1n.gif

    No loop?!?

    https://i.imgur.com/wAA2x1n.gif
  9. Replies
    19
    Views
    760

    I have a very slight bend in the neck which is...

    I have a very slight bend in the neck which is good. I Half assed Capo'd the strings at the 1st fret and when I fret them at the body joint, I have a slight gap in the middle. I don't have a feeler...
  10. Replies
    61
    Views
    1,084

    class in this place is like finger-banging a...

    class in this place is like finger-banging a prostitute with your pinkie out.

    :hide:
  11. Replies
    19
    Views
    760

    https://i.imgur.com/pX48rKf.gif

    https://i.imgur.com/pX48rKf.gif
  12. Replies
    19
    Views
    760

    I had to raise the bridge a half turn on the low...

    I had to raise the bridge a half turn on the low end and 3/4 turn on the high strings. I do have a long straight edge I was checking the relief with. I can bridge the first and 15th frets with it,...
  13. Replies
    19
    Views
    760

    This is what I ended up doing. I used my straight...

    This is what I ended up doing. I used my straight edge and the relief of the neck seemed a bit much, so I did some truss rod adjustments tonight. I took the buzz out of the upper frets but I think I...
  14. Replies
    1,030
    Views
    26,631

    https://i.imgur.com/wAP06tg.gif

    https://i.imgur.com/wAP06tg.gif
  15. Replies
    1,030
    Views
    26,631

    This is awesome. Congrats Far, you deserve...

    This is awesome.

    Congrats Far, you deserve every Rockin' note!

    https://i.imgur.com/p5Xrzp8.gif
  16. Replies
    5
    Views
    189

    I got new Preamp tubes yesterday. I'll be trying...

    I got new Preamp tubes yesterday. I'll be trying to actually fire this amp up soon enough. I haven't played hardly at all lately. :(

    New Tung Sol 12AX7's
  17. Replies
    5
    Views
    189

    There's a small rubber grommet that is missing on...

    There's a small rubber grommet that is missing on V1 test point.

    I went to Fry's and got some new fuses. Put it in, and BAM! Bias all set. All is well again. :D
  18. Replies
    5
    Views
    189

    some Biasing trouble

    The new 667 has a whole bias setup on the back of this for changing out tubes. It will take any Octal and there are test points and pots on the back.

    https://i.imgur.com/Kntdkk0.jpg?1
    ...
  19. Replies
    1,030
    Views
    26,631

    ...and you should probably let it out now.

    ...and you should probably let it out now.
  20. Replies
    1,030
    Views
    26,631

    In circuit tests are very inaccurate because...

    In circuit tests are very inaccurate because you're not measuring the part, but the whole circuit. If the resistor is connected between caps, then you'll read the resistance because the caps are an...
  21. Thread: Strings

    by Ghostman
    Replies
    16
    Views
    355

    I'm like Steve. The D'addario strings are my go...

    I'm like Steve. The D'addario strings are my go to. I hear differences in strings when I try others, but I find that the D'addario sound is like a comfort zone. They don't excel in any area, but are...
  22. Replies
    33
    Views
    706

    I have literal tears i'm laughing so damn hard.

    I have literal tears i'm laughing so damn hard.
  23. Replies
    24
    Views
    611

    luthier, tech, whatever. Just take a fucking...

    luthier, tech, whatever. Just take a fucking compliment!

    :laugh2:
  24. 1 1 = double fools day?

    1 1 = double fools day?
  25. Replies
    24
    Views
    611

    I still consider you the Master Luthier DS. ...

    I still consider you the Master Luthier DS.

    https://i.imgur.com/ioZnRLU.gif
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4